Home
Pricing

Pricing

Bunn | Ultra-2 HP White/Stainless, Manual Fill - Cleaning Card: Cleaning Instructions

Use this complete checklist on how to properly clean your Bunn coffee machine. It has the complete disassembly and cleaning step-by-step process.

MaintainX

12/07/2022

Bunn | Ultra-2 HP White/Stainless, Manual Fill - Cleaning Card: Cleaning Instructions

Use this complete checklist on how to properly clean your Bunn coffee machine. It has the complete disassembly and cleaning step-by-step process.

DISASSEMBLY & CLEANING

Turn cooling to OFF selection. Empty all product from the hopper(s). Turn auger to OFF selection.

Unplug the hopper lamp cord(s) and remove the hopper lid(s). NOTE: On Autofill models, remove the level probe and fill tubes from the hopper.

Depress the hopper lock plunger, lift slightly.

Pull the hopper assembly forward and remove.

.Pull the auger from the cooling drum.

Remove the hopper seal from the flange on the cooling drum.

CAUTION: Faucet valve is under spring tension. Spread one side of the handle first, then the other and disconnect from hopper.

Carefully slide valve up to remove spring and faucet seal. Extra care should be taken when handling the seal to prevent damage.

Remove the auger nose bushing from inside the front of the hopper. NOTE: Do not scratch this surface when cleaning. Deep scratches could cause leakage around the seal.

Remove the drip tray and cover.

Place all parts in a clean sink with mild hot water (120°F) and sanitizer solution. Allow all parts to soak for at least 5 minutes. Carefully wash all components with a clean wash cloth in the hot water and sanitizer solution. Use a clean, soft bristle brush as needed for the smaller components and tight areas. Do not immerse hopper lids. Use a commercial sanitizer that has 100 ppm of available chlorine with a concentration level of at least 3% available chlorine (KAY-5 Sanitizer). Follow the sanitizer’s mi

Wash the drum(s), hopper drip tray(s), top cover(s), and outer enclosure using a clean wash cloth that has been dampened in the hot water and sanitizer solution. Pay particular attention to the shaft area and make sure it is thoroughly cleaned and sanitized.

Thoroughly rinse all surfaces with a clean wash cloth that has been dampened with hot water. Wipe dry with a clean dry wash cloth before reassembling the dispenser

NOTE – Although most parts are dishwasher safe, they may be affected by the chemicals in some commercial sanitizing agents. Do not place the hopper nor hopper lids in a dishwasher. Rinse thoroughly before assembly.

ASSEMBLY

. Replace the auger nose bushing inside the front of the hopper.

. Install the hopper seal over the flange at the rear of the cooling drum as shown.

Align the auger shafts with the augers. Push the augers as far as they will go and rotate them so the flat face of the auger shaft is aligned with the flat face of the auger nose.

Install the hopper over the auger and cooling drum and slide it into place. Push down until the hopper lock plunger snaps into place. NOTE: On Autofill models, install the level probe and fill tubes to the hopper.

Set the hopper lid on the hopper with lamp cord at the back.

Plug in the hopper lid lamp cord.

Position the faucet seal and the return spring in the faucet valve.

Slide the faucet valve assembly into place on the hopper.

Press down on the valve to compress the spring. Position the faucet handle over the faucet valve one side at a time and snap into place on the hopper.

. Install the drip tray and cover.

Auto-fill Sanitizing Instructions

(With Internal Brixing System Installed)

Fill bucket with 4 gallons of 120 Degree F water and sanitizing solution to equal 100 ppm of available chlorine. Note: some installations may require more sanitizer solution to fill the supply lines completely.

Select “auger on” and set the cooling mode to “off” for each hopper being sanitized.

Empty product from each hopper being sanitized.

Pour one gallon of warm water into each hopper to rinse the remaining product, and then drain hopper(s).

Disconnect concentrate line from the B-I-B and set so the sanitizer can flow freely through it. Place the connector in the bottom of the sanitizer solution bucket.

Select “auger refill on” for each hopper being sanitized. Allow hoppers to fill until system reaches the fill probe. If a refill fault occurs, press the Ultra button to clear and continue filling. Repeat this process until the product line runs clear. Note: You may need to drain the hopper again and allow filling until the product line runs clear, indicating sanitizer has completely filled the lines. If the delay refill system is activated, you may also need to turn the auger off, then back to “auger refill

Select “auger off” for each hopper being sanitized.

Drain the sanitizer from the hopper(s).

Remove the B-I-B connector from the sanitizer bucket and reconnect to the product B-I-B.

Refer to the Recommended Cleaning instructions on the reverse and follow the steps to remove, clean and sanitize the hopper(s), lid(s) and other dispense parts.

Select “auger refill on” for each hopper being sanitized and allow to run until product starts flowing into the hopper(s).

Select “auger off” for each hopper being sanitized, then drain hopper(s).

The dispenser is now ready to be turned on and filled for use.

Source: MaintainX (Community Member)

Please note that any procedure, checklist, or other document available in the MaintainX Procedure Hub is provided for general education and information only and does not constitute legal, medical, or financial advice. MaintainX makes the materials available AS IS and AS PROVIDED, without warranties of any kind. By downloading or using any such materials, you assume the risk that they may not be appropriate for your specific situation and agree that you are solely responsible for any such use, including compliance with applicable law and with meeting any conditions of product warranties.

Similar procedures

Generac Diesel Generators MMG45FHKCAN6: Every 250 Hours Maintenance (Kubota Engine)
MaintainX
08/24/2022
Food Safety Checklist
MaintainX
07/23/2022
Pump Bucket Checklist Maintenance
CAF: 8
01/24/2023
Tâche mensuelle Scie à ruban
Cegep de Terrebonne
11/19/2022
Daikin Magnitude Magnetic Bearing Centrifugal Chillers(Magnitude WMC-D): During Seasonal Start Up Maintenance
MaintainX
08/10/2022
Safety Checklist for Maintenance and Cleaning of Weightlifting Gym and Equipment: As Needed Maintenance
MaintainX
09/16/2022
Equipment Specific LOTO Procedure
MaintainX
07/26/2022
Playground Safety Checklist
MaintainX
07/21/2022
JLG BOOM LIFTS E300AJ: Function Check
MaintainX
10/13/2022
Quarterly Visual Examination of Storm Water Quality
Ergon - Lubbock 14842
04/03/2022
Hot Tub Checklist: Seasonal Maintenance
MaintainX
09/08/2022
Olma LP Folder Weekly Preventive Maintenance
605 Yakima WA - Cintas
03/05/2024
Noritz N-132M-NG - Maintenance
MaintainX
08/24/2022
Tampa Terminal SIS Vibrations
Titan America - Terminals TAMPA
05/10/2024
Komatsu Bulldozer D65EX-15E0: EVERY 250 HOURS SERVICE MAINTENANCE
MaintainX
11/04/2022
Ingersoll Single Stage Electric Driven Reciprocating Air Compressor 3-5 hp (SS4L5): Daily Maintenance
MaintainX
08/24/2022
Braner Packaging line conveyors
Maas Hansen Steel
03/26/2024
Industrial Grade Wall Mount Fans 9020 - Maintenance
MaintainX
08/19/2022
Gas Station Inspection Checklist
MaintainX
07/22/2022
Caterpillar G3516 - General Maintenance
MaintainX
08/10/2022
Bunn Ultra-2 HP Manual Fill, White/Stainless - Standard Handle: Use and Care Instructions
MaintainX
12/07/2022
Crown Counterbalance Trucks SC 6000: Battery Maintenance
MaintainX
10/05/2022
Earthmoving Equipment Pre-use Inspection Checklist
MaintainX
07/15/2022
Crown Narrow-Aisle Reach Trucks RR 5200: Daily Safety Check
MaintainX
10/05/2022
Water Storage Facilities Periodic Inspection Checklist
MaintainX
07/22/2022
Hoshizaki Ice Machine (KMS-830MLH) Cleaning and Sanitizing Checklist: Monthly
MaintainX
10/08/2022
Generac Diesel Generators MMG45FHKCAN6: General Maintenance (John Deer Engine)
MaintainX
09/02/2022
Daikin Vision Semi-Custom Indoor Air Handler MD4 VFD: Every 10 Years Maintenance
MaintainX
08/10/2022
Generac Diesel Generators MLG20IF4: Daily Maintenance
MaintainX
08/30/2022
BUNN | Single® SH Soft Heat® 120/240V - Daily Cleaning Instructions
MaintainX
12/07/2022
WeatherExpert® 50LC**07-12 Single Package Rooftop Electric Cooling with Optional Electric Heat with Puron® (R-410A) Refrigerant: Monthly Maintenance
MaintainX
09/13/2022
BUNN | TB3 with Ready Light, 29" Trunk - Weekly Cleaning Instructions
MaintainX
12/13/2022
Spent Grain Bin Mechanical Running
Banks Brewery
12/12/2023
Park Safety Inspection and Maintenance Checklist
MaintainX
07/21/2022
Noritz N-063-LP - Maintenance
MaintainX
08/24/2022
Bunn CWTF15-3, Stainless Funnel (2 Upper/1 Lower Warmer) - Cleaning Card: Cleaning Instructions
MaintainX
12/07/2022
Monthly PAPR Inspection
Ergon -
02/01/2023
Scotsman Ice Machine UC2024 and UC2724: Semi-Annual Maintenance and Cleaning
MaintainX
10/08/2022
CONTROLLO QUOTIDIANO MACCHINE_plant_polonia
U.form Italy
03/22/2024
79907 | TN1 MIXER TANK Fibercel Packing Motor Check P.M.
MaintainX
05/15/2022
Lockout/Tagout Procedure for Work Orders
Amoretti/
08/14/2024
General Fire Inspection
MaintainX
10/24/2021
Toyota Pallet Trucks 6HBE30 : Scheduled Maintenance Annually or Every 1500 Operating Hours
MaintainX
11/15/2022
Mack | 2010 Mack CSM Australia Right Hand Drive - At the First Inspection Interval
MaintainX
12/28/2022
JLG | Compact Crawler Booms X14J - X390AJ - Boom Maintenance
MaintainX
10/13/2022
Weed Management Checklist
MaintainX
07/19/2022
Crown Narrow-Aisle Reach Trucks SR 5200: Daily Safety Check
MaintainX
10/05/2022
Large Golf Cart Shuttle Annually
Oklahoma School of Science and Mathemathics
04/12/2023
Daikin PreciseLine® Air Handler Sizes 006 through 050: Every 2 Years Maintenance
MaintainX
08/10/2022
Decorative Exhaust Fan Series DRLC702 - Use and Care
MaintainX
08/19/2022

Explore by industry

Manufacturing / Industrial
Property Management
General
Food & Beverage / Retail
Fleet Management
Hospitality
Healthcare

Company
About
Careers
Privacy Policy
Terms of Service

Product
Features
Pricing
Blog

Support
FAQ
API
GDPR