BUNN | NITRON® Cold Draft Single 1-Gallon Scholle Y Connector All-Black Door

1. Open dispenser door

2. Remove all product containers and place them in a refrigerated (35-40 degrees F [1.6-4.4 degrees C]) environment. Disconnect all connections to ambient products from the bottle adapter

3. Rinse all dispense stations using steps outlined in “DAILY RINSE PROCEDURE”.

DAILY RINSE PROCEDURE

4. Disconnect dispenser from power source.

5. Remove the dispense platform cover

6. Disconnect the dispense platform water line(s) from the supply line inside the refrigerated cabinet and disconnect the wiring connection(s) from the cabinet receptacle(s).

7. Remove the mounting screw(s) securing the dispense platform(s) to the cabinet

8. Pull the dispense platform(s) completely out of the cabinet and place it on a flat work surface.

9. Close the dispenser door.

10. Remove the 4 screws securing the pump head.

11. Gently pull the pump head apart

12. Gently pull the pump tube from around the pump’s rotor.

13. Release the clamps securing the old pump tubing to the plastic elbows

14. Pull the plastic elbows from the old pump tubing, and discard the old pump tubing

15. Insert the plastic elbows into the new pump tubing and secure it with the clamps.

16. Gently wrap the new pump tubing around the pump’s rotor.

17. Reassemble the pump housing onto the platform assembly

18. Repeat steps 10 through 17 for the remaining pump(s).

19. Replace the dispense platform(s) into the refrigerated cabinet, making sure to reconnect all electrical and water connections.

20. Replace the dispense platform cover.

21. Turn power on to dispenser.

22 Install containers of rinse water, run each station and check for leaks. Repair leaks as necessary.

23. Replace product shelf and product containers. Reconnect any connections to ambient product containers

24. Prime the pumps as described in “PRIMING” in the Initial Fill Section.

BUNN | NITRON® Cold Draft Single 1-Gallon Scholle Y Connector All-Black Door - Annual Preventive Maintenance

BUNN | NITRON® Cold Draft Single 1-Gallon Scholle Y Connector All-Black Door - Annual Preventive Maintenance

Annually: Replace Pump Tubing

1. Open dispenser door

2. Remove all product containers and place them in a refrigerated (35-40 degrees F [1.6-4.4 degrees C]) environment. Disconnect all connections to ambient products from the bottle adapter

3. Rinse all dispense stations using steps outlined in “DAILY RINSE PROCEDURE”.

4. Disconnect dispenser from power source.

5. Remove the dispense platform cover

6. Disconnect the dispense platform water line(s) from the supply line inside the refrigerated cabinet and disconnect the wiring connection(s) from the cabinet receptacle(s).

7. Remove the mounting screw(s) securing the dispense platform(s) to the cabinet

8. Pull the dispense platform(s) completely out of the cabinet and place it on a flat work surface.

9. Close the dispenser door.

10. Remove the 4 screws securing the pump head.

11. Gently pull the pump head apart

12. Gently pull the pump tube from around the pump’s rotor.

13. Release the clamps securing the old pump tubing to the plastic elbows

14. Pull the plastic elbows from the old pump tubing, and discard the old pump tubing

15. Insert the plastic elbows into the new pump tubing and secure it with the clamps.

16. Gently wrap the new pump tubing around the pump’s rotor.

17. Reassemble the pump housing onto the platform assembly

18. Repeat steps 10 through 17 for the remaining pump(s).

19. Replace the dispense platform(s) into the refrigerated cabinet, making sure to reconnect all electrical and water connections.

20. Replace the dispense platform cover.

21. Turn power on to dispenser.

22 Install containers of rinse water, run each station and check for leaks. Repair leaks as necessary.

23. Replace product shelf and product containers. Reconnect any connections to ambient product containers

24. Prime the pumps as described in “PRIMING” in the Initial Fill Section.