Home
Pricing

Pricing

General • Inspections

Bunn ICB Twin Soft Heat, Stainlesst: Use and Care Instructions

Use this checklist for the daily cleaning of your coffee machine. It provides many benefits including general hygiene and improving the taste of your coffee.

MaintainX

12/07/2022

Bunn ICB Twin Soft Heat, Stainlesst: Use and Care Instructions

Use this checklist for the daily cleaning of your coffee machine. It provides many benefits including general hygiene and improving the taste of your coffee.

Cleaning the Brewer

Every Day: Wipe the spreayhead panel and the entire outside surface of the brewer with a clean damp cloth.

Once a week: Remove the sprayhead by turning in a counter-clockwise direction.

Disassemble and thoroughly rinse the sprayhead. The holes must be open and clear of any mineral deposits.

Use the long end of the sprayhead cleaning tool to clean the sprayhead outlet fitting.

Re-assemble the sprayhead and install it onto the brewer.

Cleaning the Lid Assembly

Completely drain the server. Rotate handle back to release the lid lock.

Grasp the lid by the finger holds and lift the lid assembly straight up.

Clean the inlet tube with the supplied brush (00675.0000) using a mild soap solution. Rinse lid assembly thoroughly with clean water.

Cleaning the Faucet and Sight Tube

Press down on the sight gauge top to release the sight gauge tube. Remove the sight gauge tube and bottom seal.

Press down on the sight gauge top to release the sight gauge tube. Remove the sight gauge tube and bottom seal.

Unscrew the faucet cap and disassemble all the faucet parts.

Transfer the sight gauge and faucet parts to a sink with a soap solution using a mild, non-citrus, non-abrasive, liquid detergent.

Using supplied brush scrub the faucet body and sight gauge tube.

Rinse all parts in the second sink with clean hot water.

Transfer the parts to a sink filled with non-chlorine sanitizing solution. Allow the parts to soak in the sanitizing solution for a minimum of five (5) minutes.

Remove the faucet parts from the sanitizing solution, and allow to air-dry overnight. Reassemble faucet.

Cleaning the Server

Clean the faucet shank using the supplied brush (00675.0000) and cleaning solution.

Fill server with a wash solution, and thoroughly clean inside of server using a SOFT, Non-abrasive cloth or brush. Drain and thoroughly rinse using fresh water.

Re-install sight gauge seal and sight gauge tube. Re-attach faucet to server shank.

Fill the server with non-chlorine sanitizing solution, and let server sit for five (5) minutes, then drain through fully open faucet.

Clean the outside surface of the server using a clean damp cloth.

Source: MaintainX (Community Member)

Please note that any procedure, checklist, or other document available in the MaintainX Procedure Hub is provided for general education and information only and does not constitute legal, medical, or financial advice. MaintainX makes the materials available AS IS and AS PROVIDED, without warranties of any kind. By downloading or using any such materials, you assume the risk that they may not be appropriate for your specific situation and agree that you are solely responsible for any such use, including compliance with applicable law and with meeting any conditions of product warranties.

Similar procedures

Ingersoll Pressure Lubricated Reciprocating Air Compressors 5-30 HP: 4th Year Maintenance
MaintainX
08/24/2022
Generac Diesel Generators MMG25IF4: Every 250 Hours Maintenance (John Deer Engine)
MaintainX
08/24/2022
Bobcat 260 Miller Welder Inspection
Byer Steel
01/31/2023
Generac Diesel Generators MMG405: Engine and Generator Maintenance (John Deere Engine)
MaintainX
09/02/2022
Generac Diesel Generators MDG175DF4-STD3: Every 4500 Hours or 60 Months Maintenance
MaintainX
09/02/2022
JLG Vertical Mast 15VP: Daily Functional Check
MaintainX
10/13/2022
Taylor-Dunn Personal Carriers BT-280 36/48V: Pre-Operation Inspection
MaintainX
10/06/2022
Lockout/Tagout Procedure Periodic Inspection
Ergon - Lubbock 14842
08/12/2022
Noritz N-0751M-DV-LP - Maintenance
MaintainX
08/24/2022
Bunn CWTF-DV-3 Dual Volt (2 Upper/1 Lower Warmer) - Cleaning Card: Cleaning Instructions
MaintainX
12/07/2022
Allied Z-Series (3 - 6 ZCA): Annual Maintenance
MaintainX
08/24/2022
AHU Service
Radisson Blu Hotel Larnaca
04/14/2024
Toyota Pallet Trucks 8HBE40 : Every 360 Days or 2000 Deadman Hours (HD)
MaintainX
11/15/2022
Commercial Property Building Inspection Checklist
MaintainX
07/21/2022
Ingersoll Single Stage Electric Driven Reciprocating Air Compressor 3-5 hp (SS4L5): Quarterly or Every 500 Hours Maintenance
MaintainX
08/24/2022
Daikin RoofPak Forced-Draft Gas Furnace: Monthly Maintenance
MaintainX
08/10/2022
Generac Diesel Generators MMG45I: Every 500 Hours Maintenance (Isuzu Engine)
MaintainX
08/24/2022
Noritz NR71-OD-NG - Maintenance
MaintainX
08/24/2022
Crown Walkie Stackers WE/WS 2300: Daily Safety Check
MaintainX
10/05/2022
JLG | Rollback Carrier 10Ton RS - Walk-Around Inspection
MaintainX
10/13/2022
Crown Rider Pallet Trucks GPC 3000: Daily Safety Inspection
MaintainX
10/05/2022
Daikin Templifier TEMPLIFIER® SCROLL WATER HEATER Scroll TGZ-B: Annual Maintenance
MaintainX
08/10/2022
Ingersoll Two-Stage Electric Driven Reciprocating Air Compressor 2-5 hp: Monthly Maintenance
MaintainX
08/24/2022
JLG Vertical Mast AM-30: Function Check
MaintainX
10/13/2022
Generac Diesel Generators MMG35FHDCAN6: Every 500 Hours Maintenance (Kubota Engine)
MaintainX
08/24/2022
Generac Diesel Generators MMG25FHI: Daily Maintenance (Isuzu Engine)
MaintainX
08/30/2022
Caterpillar TH360B Telehandler: Maintenance (When Required)
MaintainX
08/10/2022
Urgent Repair
Proactive MD
03/29/2022
Performance Climate Changer® Air Handlers Sizes 3-120 for Indoor and Outdoor Units - After 48 Hours of Operation Maintenance Checklist
MaintainX
08/10/2022
Daikin Custom Air Handler MD4 VFD: Every 3 Years Maintenance
MaintainX
08/10/2022
Generac Gaseous Generators MGG210: Every 750 Hours Maintenance
MaintainX
08/24/2022
Industrial Grade I-Beam Mount Fans 9675 - Maintenance
MaintainX
08/19/2022
Under Cabinet Range Hood Shells RS303 - Maintenance
MaintainX
08/19/2022
Caterpillar SR4B: Maintenance Interval Schedule (Standby)(Every 7500 Hours or 1 Year)
MaintainX
08/10/2022
Yale Forklift ERC060RG: Every 8 Hours or Daily Maintenance
MaintainX
10/25/2022
Equipment/Vehicle Pre-Start Checklist
MaintainX
07/15/2022
Generac Diesel Generators MLG20ICAN (MLG15)): Every 500 Hours Maintenance
MaintainX
08/24/2022
Park Maintenance Standard: Turf Management - Level 1
MaintainX
07/21/2022
Cut Machine PM
wesco dist
01/27/2023
Monthly Freezer Door Cleaning
Pacific Seafood - Woodland
05/07/2024
Copy - Generic Golf Carts and Utility Vehicles Safety Inspection Checklist
Lakeside Golf Club
05/21/2023
Carpet Extractor - Weekly
Oklahoma School of Science and Mathemathics
04/21/2023
Rolling Tower Inspection Checklist Form
MaintainX
07/26/2022
Verification Record for Timing Devices
Ergon - Lubbock 14842
05/23/2022
Jet Ski Inspection Checklist
MaintainX
07/22/2022
Bunn ICB-DV Dual Volt Tall Platinum Edition: Weekly Cleaning and Maintenance
MaintainX
12/13/2022
Separated Combustion Indoor Gas Fired Make-Up Air Units - Seasonal Maintenance
MaintainX
08/06/2022
Hoshizaki Ice Machine (KMS-822MLH) Cleaning and Sanitizing Checklist: Monthly
MaintainX
10/08/2022
Agility™ Centrifugal Water-Cooled Chiller - Weekly Maintenance
MaintainX
08/10/2022
Hoshizaki Ice Machine KMD-410MAH, MWH, MRH KMD-460MAH, MWH, MRH KMD-530MAH, MWH, MRH Cleaning and Sanitizing Checklist: Daily
MaintainX
10/08/2022

Explore by industry

Manufacturing / Industrial
Property Management
General
Food & Beverage / Retail
Fleet Management
Hospitality
Healthcare

Copyright © 2024 MaintainX. All rights reserved.

Company
About
Careers
Privacy Policy
Terms of Service

Product
Features
Pricing
Blog

Support
FAQ
API
GDPR