Back
Manufacturing / Industrial • Maintenance

Doosan D30S-5 Pneumatic Forklift 250 Hours/ Weekly

The Doosan D30S-5 Pneumatic Forklift 250 Hours/ Weekly ensures the quality performance of your forklift by identifying parts to replace/repair. Ensure the lifespan of your is preserved.
MaintainX
04/26/2021

Doosan D30S-5 Pneumatic Forklift 250 Hours/ Weekly

The Doosan D30S-5 Pneumatic Forklift 250 Hours/ Weekly ensures the quality performance of your forklift by identifying parts to replace/repair. Ensure the lifespan of your is preserved.

    Hydraulic Return Filter – Change

    WARNING: Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.

    Park the lift truck level with the forks lowered, parking brake engaged, transmission in NEUTRAL and the engine stopped.

    • 25.PNG

    Air Intake System - Check, Clean

    Precleaner (If Equipped)

    NOTICE Never service cleaner with the engine running.

    • 26.PNG

    Servicing Filter Element

    NOTICE: Never service filter with the engine running.

    Service the air cleaner when the red target in the service indicator stays locked in the visible position with the engine stopped.

    • 28.PNG

    NOTICE : Do not allow dirty air to enter the intake hose when cleaning the inside of the air cleaner housing.

    Cleaning Primary Filter Elements

    WARNING: Pressure air can cause personal injury. When using pressure air for cleaning, wear a protective face shield, protective clothing and protective shoes. The maximum air pressure must be below 205 kPa (30 psi) for cleaning purposes.

    NOTICE: Do not clean the elements by bumping or tapping them. Inspect filter elements after cleaning. Do not use a filter with damaged pleats, gaskets or seals.

    When cleaning with pressure air, use 205 kPa (30 psi) maximum pressure to prevent filter element damage. When cleaning with pressure water, use 280 kPa (40 psi) maximum pressure to prevent filter element damage.

    Have spare elements on hand to use while cleaning used elements. The primary element should be replaced after 6 months service or after cleaning no more than 3 times.

    Air-205 kPa (30 psi) Maximum Pressure

    Water-280kPa (40 psi) Maximum Pressure

    Detergent

    Checking Element

    Brake Oil Level - Check

    The brake reservoir is located on the left side of the steering column.

    Hydraulic Oil Level – Check

    WARNING: At operating temperature, the hydraulic tank is hot and under pressure. Hot oil can cause burns. Remove the filter cap only when the engine is stopped, and the cap is cool enough to touch with your bare hand. Remove the filter cap slowly to relie

    • 33.PNG

    Drive Axle Oil Level - Check

    Park the lift truck on a level surface. Apply the parking brake. The engine at low idle. Place the directional control lever in NEUTRAL.

    • 34.PNG

    Mast, Carriage, Lift Chains & Attachments - Inspect, Lubricate

    • 35.PNG

    NOTICE: Lubricate chains more frequently than normal in applications where the lift truck is operating in an atmosphere which could cause corrosion of components or when lift truck must work in rapid lift cycles.

    Steering Mechanism - Check, Lubricate

    Battery Terminal - Clean, Inspect

    WARNING: Batteries give off flammable fumes that can explode. Do not smoke when observing the battery electrolyte levels. Electrolyte is an acid and can cause personal injury if it contacts skin or eyes. Always wear protective glasses when working with ba

    • 37.PNG

    Engine Oil & Filter (LP & Gasoline Engine Only) - Change

    Gasoline, LP Engine Crankcase

    WARNING: Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.

    • 38.PNG
    • 39.PNG

    PCV Valve System - Inspect, Clean

    G420F(E) Gasoline, LP and Dual Fuel Engines

    G424F(E) LP and Duel Fuel Engines

    G424I(E) LP and Duel Fuel Engines

    G430FE LP Engine

    Wheel Bolts & Nuts - Inspect

    Inspect Tightness (D, G - Series)

    Steer Wheels

    Drive Wheels

    Inspect Tightness (GC - Series)

    Drive Wheels

Source: Doosan

Please note that any procedure, checklist, or other document available in the MaintainX Procedure Hub is provided for general education and information only and does not constitute legal, medical, or financial advice. MaintainX makes the materials available AS IS and AS PROVIDED, without warranties of any kind. By downloading or using any such materials, you assume the risk that they may not be appropriate for your specific situation and agree that you are solely responsible for any such use, including compliance with applicable law and with meeting any conditions of product warranties.