Cleaver Brooks Flexible Watertube Skid Solutions 750-394 Maintenance

boiler

• Yes
• No
• N / A

including burner

• Yes
• No
• N / A

trim

• Yes
• No
• N / A

controls

• Yes
• No
• N / A

Is the burner fuel and pilot supply properly installed according to manual?

• Yes
• No
• N / A

If dual fuel, are both fuels available for start-up?

• Yes
• No
• N / A

Are the skids level?

• Yes
• No
• N / A

Where required, will qualified boiler operators be present for start-up?

• Yes
• No
• N / A

Will operating personnel be available for training during start-up?

• Yes
• No
• N / A

Will a person be available if needed to assist the service technician with miscellaneous tasks in the boiler room?

• Yes
• No
• N / A

Have all skid piping connections been completed?

• Yes
• No
• N / A

A full capacity load (sufficient for high fire fuel/air ratio adjustment) will be required for complete burner adjustment. Can this load be absorbed by the system, and have provisions been made to put a full load on the boiler during start-up?

• Yes
• No
• N / A

Is all accessory equipment properly vented according to equipment manuals?

• Yes
• No
• N / A

Is the boiler, burner, and auxiliary equipment installed in accordance with the manufacturer's and insurer's requirements, and applicable insurance and regulatory codes?

• Yes
• No
• N / A

Is the safety relief valve (s) properly installed?

• Yes
• No
• N / A

Is the safety relief valve (s) discharge piping properly installed with no weight or strain on the valve (s)?

• Yes
• No
• N / A

Are relief valves piped to a safe discharge, and are the drain lines installed in accordance with all applicable regulatory codes?

• Yes
• No
• N / A

Is the return water temperature thermometer installed in the system return fitting? [Applicable to hot water units only].

• Yes
• No
• N / A

Has the boiler air vent been properly piped or an auto air vent device supplied to eliminate air entrapment? [Applicable to hot water units only].

• Yes
• No
• N / A

If supplied, has the stack thermometer been installed?

• Yes
• No
• N / A

Has the breeching/stack been properly installed?

• Yes
• No
• N / A

Has the source of combustion air been verified and properly sized?

• Yes
• No
• N / A

Have all shipped loose items been accounted for and installed?

• Yes
• No
• N / A

Is the available power supply (voltage, phase, and hertz) correct per the skid panel data plate and wiring diagram information?

• Yes
• No
• N / A

Have all electrical connections been made for the boiler, burner, and all auxiliary equipment?

• Yes
• No
• N / A

Have emergency and safety devices been installed in accordance with regulatory codes?

• Yes
• No
• N / A

Have all boiler field-wired connections been made according to the wiring diagram supplied by Cleaver-Brooks for the particular installation?

• Yes
• No
• N / A

Is the equipment properly grounded to earth ground?

• Yes
• No
• N / A

Has the make-up water system and pressure regulating valve been connected and are they operable?

• Yes
• No
• N / A

Has the boiler and system been filled with properly treated water at a minimum of 70 degrees Fahrenheit (21.1 Celsius)?

• Yes
• No
• N / A

Have the boiler and system been pressure tested to check for leaks?

• Yes
• No
• N / A

Has the system piping been flushed and cleaned or will this be accomplished during start-up?

• Yes
• No
• N / A

Have all fuel lines been pressure tested according to local codes, then purged of air?

• Yes
• No
• N / A

Is fuel pressure and volume sufficient for the boiler (s) at maximum firing rate as stated on the nameplate?

• Yes
• No
• N / A

Are gas pressure gauges installed and are they indicating proper gas pressure upstream of the boiler mounted gas regulator?

• Yes
• No
• N / A

Are gas vents including vent valves, properly piped to a point of safe discharge?

• Yes
• No
• N / A

Has insurance inspection, if required, been completed?

• Yes
• No
• N / A

If upstream gas pressure exceeds 5 psig (34.5 kpa), have gas pressure relief valves been installed?

• Yes
• No
• N / A