Elastic Recovery and Force Ductility Mold Verification Record
Title: Elastic Recovery and Force Ductility Mold Verification Record Description: This form is used to record measurements for verifying the compliance of molds with specified dimensions and tolerances. It includes detailed inspection criteria and maintenance items to ensure the molds meet the required standards. Introduction: The Elastic Recovery and Force Ductility Mold Verification Record (PTQM-FO-026.02) is designed to document the measurements and conditions of molds used in production.
Ergon - Lubbock 14842
06/10/2024
Elastic Recovery and Force Ductility Mold Verification Record
This procedure is used to record measurements for verifying the compliance of molds with specified dimensions and tolerances. It includes detailed inspection criteria and maintenance items to ensure the molds meet the required standards.
Date
Performed By
Equipment/Model
Caliper ID
Mold 1
Fill in values measured (mm)
(A) Outside width of center inset (35.5-36.5 mm)
Center a
Center a'
(B) Inside width of center insert (29.5-30.5 mm)
Center a
Center a'
(C) Height of the center insert (16.75-17.25 mm)
Center a
Center a'
(D) Sample cross sectional area (9.90-10.10 mm)
Center a
Center a'
Mold 2
Fill in values measured (mm)
(A) Outside width of center inset (35.5-36.5 mm)
Center a
Center a'
(B) Inside width of center insert (29.5-30.5 mm)
Center a
Center a'
(C) Height of the center insert (16.75-17.25 mm)
Center a
Center a'
(D) Sample cross sectional area (9.90-10.10 mm)
Center a
Center a'
Mold 3
Fill in values measured (mm)
(A) Outside width of center inset (35.5-36.5 mm)
Center a
Center a'
(B) Inside width of center insert (29.5-30.5 mm)
Center a
Center a'
(C) Height of the center insert (16.75-17.25 mm)
Center a
Center a'
(D) Sample cross sectional area (9.90-10.10 mm)
Center a
Center a'
Mold 4
Fill in values measured (mm)
(A) Outside width of center inset (35.5-36.5 mm)
Center a
Center a'
(B) Inside width of center insert (29.5-30.5 mm)
Center a
Center a'
(C) Height of the center insert (16.75-17.25 mm)
Center a
Center a'
(D) Sample cross sectional area (9.90-10.10 mm)
Center a
Center a'
Mold 5
Fill in values measured (mm)
(A) Outside width of center inset (35.5-36.5 mm)
Center a
Center a'
(B) Inside width of center insert (29.5-30.5 mm)
Center a
Center a'
(C) Height of the center insert (16.75-17.25 mm)
Center a
Center a'
(D) Sample cross sectional area (9.90-10.10 mm)
Center a
Center a'
Mold 6
Fill in values measured (mm)
(A) Outside width of center inset (35.5-36.5 mm)
Center a
Center a'
(B) Inside width of center insert (29.5-30.5 mm)
Center a
Center a'
(C) Height of the center insert (16.75-17.25 mm)
Center a
Center a'
(D) Sample cross sectional area (9.90-10.10 mm)
Center a
Center a'
Mold 7
Fill in values measured (mm)
(A) Outside width of center inset (35.5-36.5 mm)
Center a
Center a'
(B) Inside width of center insert (29.5-30.5 mm)
Center a
Center a'
(C) Height of the center insert (16.75-17.25 mm)
Center a
Center a'
(D) Sample cross sectional area (9.90-10.10 mm)
Center a
Center a'
Maintenance Items
Visually inspect for any defects. If molds do not conform to requirements, remove from service and replace.
Action Recommended
Comments
Source: Ergon - Lubbock 14842 (Community Member)