Back
Manufacturing / Industrial • Maintenance

Hyster S60FT 4 Wheel Cushion Tire 500 Hours /3 Months

The Hyster S60FT 4 Wheel Cushion Tire 500 Hours /3 Months Form ensures your equipment is running properly, avoiding costly downtime and extending the life cycle of the equipment. Ultimately, this form helps you save time and money. It also has safety precautionary measures to ensure the safety of our employees.
MaintainX
04/26/2021

Hyster S60FT 4 Wheel Cushion Tire 500 Hours /3 Months

The Hyster S60FT 4 Wheel Cushion Tire 500 Hours /3 Months Form ensures your equipment is running properly, avoiding costly downtime and extending the life cycle of the equipment. Ultimately, this form helps you save time and money. It also has safety precautionary measures to ensure the safety of our employees.

    HYDRAULIC OIL S40-70FT, S55FTS (F187)

    WARNING : At operating temperature the hydraulic oil is HOT. Do not permit the hot oil to touch the skin and cause a burn.

    CAUTION : Do not permit dirt to enter the hydraulic system when the oil level is checked or the filter is changed. Never operate the hydraulic pump without oil in the hydraulic system. The operation of the hydraulic pump without oil will damage the pump.

    BATTERY AND CABLE TERMINALS

    CAUTION: DO NOT try to start the engine by pushing or towing the lift truck. Damage to the transmission can occur if engine is started by pushing or towing lift truck.

    If the battery becomes discharged and requires a booster battery to start the engine, follow these procedures carefully when connecting the jumper cables:

    ENGINE OIL FILTER

    DRIVE BELT

    ENGINE IDLE SPEEDENGINE IDLE SPEED

    ENGINE GOVERNED SPEED

    ENGINE GOVERNED SPEED

    FORKS

    NOTE: Forks must be removed or installed by trained personnel only.

    The identification of a fork describes how the fork is con- nected to the carriage. These lift trucks have hook forks.

    Forks, Remove

    NOTE: If lift truck is equipped with a fork positioner attach- ment, perform Step 1 first, before going to Step 2. If lift truck is not equipped with a fork positioner attachment, go to Step 2.NOTE: If lift truck is equipped with a fork positioner attach-

    • 37.png

    WARNING: Do not try to move a fork without a lifting device. Each hook fork for these lift trucks can weigh 45 to 115 kg (99 to 253 lb).

    NOTE: Forks are to be replaced only in sets and not indi- vidually.

    MAST

    HEADER HOSES

    WARNING :Lower the lift mechanism completely. Never allow any person under a raised carriage. Do not put any part of your body in or through the lift mechanism unless all parts of the mast are completely lowered and the engine is STOPPED.

    Do not try to correct the alignment of the fork tips by bending the forks or adding shims. If either fork is damaged, replace the forks as a set. Never repair damaged forks by heating or welding. Forks are made of special steel using special proce- dures.

    Inspect the welds on the:

    Make sure that the capscrews and nuts are tight.

    Visually inspect hoses/fittings for hydraulic

    leaks

    hose cover for cuts

    cracks

    defective/ broken clamping devices or sheaves

    proper tracking during operation

    LIFT CHAINS

    Figure 33. Lift Chain Check

    MAST

    INTEGRAL SIDESHIFT CARRIAGE

    MAST

    MAST

    BRAKE FLUID

    BRAKE OIL

    STEERING AXLE

    Dry Brakes S40-70FT, S55FTS (F187)

    Wet Brakes - Iron Case H40-70FT (L177)

    Wet Brakes - Aluminum Case H40-70FT (L177)

    LEFT SIDE

    Right Side

Source: Hyster

Please note that any procedure, checklist, or other document available in the MaintainX Procedure Hub is provided for general education and information only and does not constitute legal, medical, or financial advice. MaintainX makes the materials available AS IS and AS PROVIDED, without warranties of any kind. By downloading or using any such materials, you assume the risk that they may not be appropriate for your specific situation and agree that you are solely responsible for any such use, including compliance with applicable law and with meeting any conditions of product warranties.